Interlux Ultra-Kote Hard Antifouling Bottom Paint

Interlux Ultra-Kote Hard Antifouling High Copper Bottom Paint

The Interlux Ultra-Kote is a high performance antifouling paint that is perfect for areas that experience moderate to severe fouling. Designed to provide maximum performance, the high copper hard coating provides excellent long term protection from shell fouling, such as barnacles. Thanks to the fast drying formula Ultra-Koat allows you to paint and launch in the same day. Can be used on Fiberglass, wood, or properly primed still with the addition of color stability for a uniform look. Able to be used in fresh water, salt water, & brackish water.

Note: Green Ultra-Kote (Part Number Y3559U1) is not available to ship to California

Features:

• Works on Fiberglass, wood, and steel boats
• For use in Fresh water, Salt water, & Brackish water
• Fast dry formula
• High Copper
• Long term protection

Specifications:

• Pack Size: US Gallon
• Finish: Matte
• Recommended usage: All fouling waters
• Colors Available: Red (Y3449U), Green (Y3559U), Blue (Y3669U), Black Y3779U
• Drying time: Touch dry 1hrs; To launch 8hrs. @73° F
• Number of Coats: 2 coats, 3 on bare wood (first coat thinned)
• Coverage: 506 ft²/gal
• VOC: 327 g/lt

How to Apply Interlux Ultra-Kote Hard Antifouling Bottom Paint

Application Tips

• Mixing: Stir or shake contents thoroughly before use
• Thinner: Special Thinner 216 or Brush Ease 433
• Thinning: Thin only if necessary. Thin no more than 10% (except conventional spray). Use Brush Ease 433 if roller or brush drags during application
• Cleaner: Special Thinner 216 or Brush Ease 433

Applicators

• Airless Sprayer
• Pressure: 170-204 bar/2500-3000 psi
• Tip Size: .53mm /21 thou.
• Must be thinned 5-10% bu volume with Special Thinner 216
• Conventional Spray
• Pressure Pot: Pressure : 3.44-4.47 bar/50-65 psi (gun pressure); 10-15 psi (pot pressure)
• Tip Size: 1.83-2.2 mm/70-85 thou.
• Thin 10-15" with Special Thinner 216 for application by Pressure Pot
• Roller
• Use a 3/8" nap solvent resistant roller

Surface Preparation

• Good Condition
• Remove all traces of loose paint & contamination by sanding
• Sand using an 80 grit wet-dry sandpaper
• Remove sanding residue
• Poor Condition
• Completely remove all old antifouling paint
• For Fiberglass & wood use Interstrip 299E
• For Steel sandblast to a near white metal
• Bare Fiberglass Preparation
• Fiberglass must be properly prepared to prevent delamination
• Remove mold release wax using Fiberglass Surface Prep YMA601V or Fiberglass Solvent Wash 202
• Fill any surface imperfections with Interlux Watertite
• Once surface is properly prepared follow the application system below
• Bare Fiberglass - No Sanding System
• Clean following the above preparation procedure
• Apply one coat of Interprotect 2000E or Fiberglass No-Sand Primer
• Following overcoating guidelines for the primer, apply 2 coats of Ultra-Kote allowing appropriate drying times
• Bare Fiberglass - Sanding System
• Clean following the above preparation procedure
• Sand with 80 grade (grit) paper
• Remove sanding residue
• Apply at least 2 coats of Ultra-Kote allowing for appropriate dry times
• Bare Fiberglass - Blister Prevention System
• Clean following the above preparation procedure
• Sand with 80 grade (grit) paper
• Remove sanding residue
• Apply Interprotect 2000E to a thickness of 10 mils
• Apply at least two coats of Ultra-Kote unthinned, allowing for the appropriate dry times
• Barewood
• Sand with 80 grade (grit) paper
• Remove sanding residue
• Apply the first coat of Ultra-Kote thinned 10% with Special Thinner 216 or Brush-Ease 433
• If necessary, fill seams with Seam Compound Brown 30
• Apply 2 or more coats of Ultra-Kote unthinned, allowing for appropriate dry times
• Underwater Metals
• Do NOT use on aluminum
• Contact Interlux Technical Service Dept. 1-800-468-7589 for full information

Click here to download Interlux Ultra-Kote Application Guide

California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov