Pettit Inflatable Boat Bottom Paint

Pettit Inflatable Boat Bottom Paint

Pettit's Inflatable Boat Bottom Paint is a water-based paint that provides multi-season protection against algae, barnacles, and all types of marine and fresh water fouling. Its water-based formula results in a product that is easy to apply, environmentally responsive, and is safer to use. This bottom paint exceeds even the most stringent air pollution (VOC) regulations. Pettit's Inflatable Boat Bottom Paint withstands frequent trailering, beaching, and launching while offering excellent antifouling protection. This paint is resistant to cracking, peeling, and flaking and is suitable for use on PVC or Hypalon.

Features:

• Water-based formula
• Ablative technology eliminates sanding and paint build-up
• Environmentally friendly, easy to apply and cleanup with soap & water
• Unlimited dry time to launch - can be painted in fall or winter
• Complies with all air pollution (VOC) regulations
• Contains PTFE which reduces drag
• Sold in quarts

Specifications:

• Color: Black
• Finish: Flat
• Coverage: 430 sq. ft/gal
• Number of Coats: 2 Minimum
• Application Methods: Brush, roller, airless or conventional spray
• VOC: 150 g/l max.
• Biocide: Cuprous Oxide 25.25%

Associated Products:

Pettit 120 Brushing Thinner - For surface prep

Pettit 97 Epoxy Thinner - For surface prep

How to Apply Pettit Inflatable Boat Bottom Paint

Pettit's Inflatable Boat Bottom paint is very easily applied by brush, roller, or spray. It is necessary to thoroughly mix Pettit Inflatable Boat Bottom Paint prior to application. Before using, check sides and bottom of can to make sure all the pigment has been mixed in. When rolling, thin the paint approximately 5-10% with clean fresh water and wet the surface to be painted with clean fresh water as well. This aids the "hold out" of the coating, resulting in truer color and smoother finish.

• Application Methods: Brush, Roller, Airless or Conventional Spray.
• Number of Coats: 2 minimum with additional coat at waterline recommended.
• Dry Film Thickness: 1.5 mils (3.75 wet mils)
• Coverage: 430 sq. ft/gal.
• Application Temp: 50°F Min. / 90°F Max.
• Thinner: Clean, fresh water

Application Systems

• Rubberized Fabric Surfaces
• Wash surface to be painted with a mild detergent and water solution, then rinse thoroughly with clean water. Allow to dry.
• Pour a moderate amount of of 97 Epoxy Thinner onto a bronze wood pad.
• Choose a small area and scrub the surface lightly but thoroughly. Wipe off any excess 97 Epoxy Thinner.
• Repeat the process until the entire surface to be painted has been scrubbed and wiped clean.
• Apply a generous coat of Inflatable Boat Bottom Paint.
• Allow the paint to dry to recoat and apply a second full coat.
• Fiberglass Surfaces
• Wash the fiberglass with Pettit 97 Epoxy Thinner to remove grease and dirt.
• Sand thoroughly with 80 grit sandpaper to a dull, frosty finish.
• Rewash sanded surface with 97 Epoxy Thinner.
• Apply at least two coats of Inflatable Boat Bottom Paint.
• Previously Coated Surfaces
• To repaint surfaces painted with this product:
• Scrub the finish with an abrasive pad and recoat with a fresh coat of Inflatable Boat Bottom Paint.
• To paint old, hard antifoulings:
• Thoroughly wipe down the surface with 120 Brushing Thinner.
• Sand surface with 80 grit sandpaper. Wipe clean with 120 Brushing Thinner.
• Apply Inflatable Boat Bottom Paint.
• To paint old tin or copper copolymers or Teflon-based paints:
• Sand thoroughly with 80 grit sandpaper to remove chalky outer surface.
• Wipe clean of sanding residue.
• Overcoat directly with Inflatable Boat Bottom Paint.
• Traditional, soft antifoulings should be removed before applying Inflatable Boat Bottom Paint.

Do not use Pettit Inflatable Boat Bottom Paint on aluminum hulls, outdrives, or lower units.

Click to Download Pettit Inflatable Boat Bottom Paint Application Instructions

California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov